CL5

20800,00 HT

Table de mixage numérique 72 pistes Yamaha
Référence : CL5
Compatible stage Rio

Avec ses trois sections de faders entièrement configurables, la CL5 est le choix idéal pour un large panel d’applications de systèmes de sonorisation « Live ».

  • Canaux d’entrées : 72 mono, 8 stéréo.
  • Faders : 16 faders section de gauche, 8 faders section Centralogic, 8 faders section de droite, 2 faders section master .
  • Support en alu pour iPad.
  • Bandeau de bar-graphes intégré

Description

Console audio Yamaha CL5

Comparatif consoles série CL

CL5 CL3 CL1
General specifications
Sampling frequency rate Internal 44.1kHz / 48kHz 44.1kHz / 48kHz 44.1kHz / 48kHz
External 44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm) 44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm) 44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm)
Signal delay Less than 2.5ms, OMNI IN to OMNI OUT, Fs=48kHz Less than 2.5ms, OMNI IN to OMNI OUT, Fs=48kHz Less than 2.5ms, OMNI IN to OMNI OUT, Fs=48kHz
Total harmonic distortion Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω, OMNI IN to OMNI OUT, Input Gain = Min. Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω, OMNI IN to OMNI OUT, Input Gain = Min. Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω, OMNI IN to OMNI OUT, Input Gain = Min.
Frequency response +0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, OMNI IN to OMNI OUT +0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, OMNI IN to OMNI OUT +0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, OMNI IN to OMNI OUT
Dynamic range 112dB typ.: DA Converter / 108dB typ.: OMNI IN to OMNI OUT, Input Gain = Min. 112dB typ.: DA Converter / 108dB typ.: OMNI IN to OMNI OUT, Input Gain = Min. 112dB typ.: DA Converter / 108dB typ.: OMNI IN to OMNI OUT, Input Gain = Min.
Hum & noise level Equivalent input noise -128dBu typ., Equivalent Input Noise, Input Gain=Max. -128dBu typ., Equivalent Input Noise, Input Gain=Max -128dBu typ., Equivalent Input Noise, Input Gain=Max
Residual output noise -88dBu, Residual output noise, ST master off -88dBu, Residual output noise, ST master off -88dBu, Residual output noise, ST master off
Crosstalk -100dB*1, adjacent OMNI IN/OMNI OUT channels, Input Gain = Min. -100dB*1, adjacent OMNI IN/OMNI OUT channels, Input Gain = Min. -100dB*1, adjacent OMNI IN/OMNI OUT channels, Input Gain = Min.
Power requirements US/Canada: 120V 60Hz, Japan: 100V 50/60Hz, China: 110-240V 50/60Hz, Korea: 220V 60Hz, Other: 110-240V 50/60Hz US/Canada: 120V 60Hz, Japan: 100V 50/60Hz, China: 110-240V 50/60Hz, Korea: 220V 60Hz, Other: 110-240V 50/60Hz US/Canada: 120V 60Hz, Japan: 100V 50/60Hz, China: 110-240V 50/60Hz, Korea: 220V 60Hz, Other: 110-240V 50/60Hz
Power consumption 170W: Internal Power Supply / 200W: Simultaneous use of Internal PSU and External PW800W 170W: Internal Power Supply / 200W: Simultaneous use of Internal PSU and External PW800W 170W: Internal Power Supply / 200W: Simultaneous use of Internal PSU and External PW800W
Dimensions W 1053mm (41 1/2in) 839mm (33 1/8in) 648mm (25 5/8in)
H 299mm (11 3/4in) 299mm (11 3/4in) 299mm (11 3/4in)
D 667mm (26 1/4in) 667mm (26 1/4in) 667mm (26 1/4in)
Net weight 36kg (79.4lb) 29kg (63.9lb) 24kg (52.9lb)
Others Temperature Range: Operating temperature range: 0 – 40°C, Storage temperature range: -20 – 60°C Temperature Range: Operating temperature range: 0 – 40°C, Storage temperature range: -20 – 60°C Temperature Range: Operating temperature range: 0 – 40°C, Storage temperature range: -20 – 60°C

Analog input characteristics

Input Terminals GAIN Actual Load
Impedance
For use with nominal Input level Connector
Sensitivity*¹ Nominal Max. before clip
OMNI IN 1-8 +66dB 7.5kΩ 50-600Ω Mics &
600Ω Lines
-82dBu (61.6μV) -62dBu (0.616mV) -42dBu (6.16mV) XLR3-31 type (Balanced)*²
-6dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
TALKBACK +64dB 10kΩ 50-600Ω Mics &
600Ω Lines
-70dBu (0.245mV) -60dBu (0.775mV) -40dBu (7.75mV) XLR3-31 type(Balanced)*²
+20dB -26dBu (38.8mV) -16dBu (0.123V) +4dBu (1.23V)

*1. Sensitivity is the lowest level that will produce an output of +4dBu(1.23V) or the nominal output level when the unit is set to maximum gain.(all faders and level controls are maximum position.)
*2. XLR-3-31 type connectors are balanced..(1=GND, 2=HOT, 3=COLD)
*3. In these specifications, 0dBu = 0.775 Vrms.
*4. All input AD converters are 24bit linear, 128times oversampling.
*5. +48V DC ( phantom power ) is supplied to OMNI IN (1-8) and TALKBACK XLR type connectors via each individual software controlled switches.

Analog output characteristics

Output Terminals Actual Source
Impedance
For Use With
Nominal
Max.Output Level
Select SW*4
Output Level Connector
Nominal Max. before clip
OUTPUT 1-8 75Ω 600Ω Lines +24dB (default) +4dBu (1.23 V) +24dBu (12.3V) XLR-3-32 type (Balanced)*1
+18dB -2dBu (616mV) +18dBu (6.16V)
OUTPUT 9-16*5 75Ω 600Ω Lines +24dB (default) +4dBu (1.23 V) +24dBu (12.3V) XLR-3-32 type (Balanced)*1
+18dB -2dBu (616mV) +18dBu (6.16V)

*1. XLR-3-32 type connectors are balanced.( 1=GND, 2=HOT, 3=COLD )
*2. In these specifications, 0dBu = 0.775 Vrms.
*3. All output DA converters are 24bit, 128times oversampling.
*4. There are switches inside the body to preset the maximum output level. *5. Rio3224-D only

Digital Input & Output Characteristics

Terminal Format Data length Level Audio Connector
Primary/Secondary Dante 24bit or 32bit 1000Base-T 24ch Input/32ch Output (Rio3224-D) 8ch Input/16ch Output (Rio1608-D) 8ch Output (Ri8-D) 8ch Input (Ro8-D) etherCON Cat5e (Rio3224-D, Rio1608-D) RJ-45 (Ri8-D, Ro8-D)

Digital Output Characteristics

Terminal Format Data length Level Connector
AES/EBU OUT 1-4*1 AES/EBU AES/EBU Professional Use 24bit RS422 XLR-3-32 type (Balanced)*2

*1 Rio3224-D only
*2. XLR-3-32 type connectors are balanced.( 1=GND, 2=HOT, 3=COLD )

Control I/O characteristics

Each I/O Slot accepts a Mini-YGDAI card. Only Slot1 has a serial interface.

Terminal Format Level Connector
MIDI IN MIDI DIN Connector 5P
OUT MIDI DIN Connector 5P
WORD CLOCK IN TTL/75Ω terminated BNC Connector
OUT TTL/75Ω BNC Connector
GPI (5IN/5OUT) D-Sub Connector 15P (Female) *1
NETWORK IEEE802.3 10BASE-T/100Base-TX/ RJ-45
LAMP (CL5=3, CL3=2, CL1=1) 0V – 12V XLR-4-31 type *2
USB HOST USB 2.0 USB A Connector (Female)-
Meter Bridge (CL3/CL1 only) D-Sub Connector 9P (Female)-

*1. Input pins: Internal TTL-level pull-up resistors provided (47kΩ). Output pins: Open-drain output (Vmax = 12V, max. sink current/pin = 75mA) Power pins: Output voltage Vp = 5V, max. output current Imax = 300mA
*2. Pin 4 = +12V, Pin 3 = GND, lamp rating 5W. Software voltage control.

Autres références chez Yamaha

Surface de contrôle

Mixette

Stage box et interfaces

  • Rack de 8 entrées avec réseau Dante : RI8B
  • Boitier de scène 16 pistes avec réseau dante : Rio 1608D
  • Boitier de scène 32 pistes avec réseau dante : Rio 3224 D
  • Convertir Dante et Madi : RMio64-D I/O Rack
  • Rack de 8 sorties ligne en XLR, entrées Dante, 1U : Ro8-D
  • Interface audio pour convertir le Dante et les cartes Mini-YGDAI ,  64 inputs and 64 outputs : RSio64-D
  • Boitier de scène économique 16 pistes avec réseau dante : Tio 1608 

Options

Voir aussi