| Model |
LM 26 |
Features
|
| Module configuration |
2 Contour or 4 Mesa modules |
| Channel processing |
6 in Contour mode, 4 in Mesa mode |
| Input routers |
8 input routers with 4 priorities in each, seamless failover to lower priorities |
| Module input mixer |
4 ch. for Contour, 8 ch. for Mesa-modules. Mix any ratio between all input routers. |
| Input processing |
Raised Cosine Mesa and Ideal Graphic input equalizers |
| Output processing |
Linear phase or Classic crossovers, Parametric EQ, shelving and all-pass filters |
| Features |
Delay, Mute, Phase, Gain etc. |
| Limiters |
LimiterMax with Peak and RMS limiter. Configurable MaxRMSLevel, MaxRMSCorner, MaxRMSAttack |
| SuperModule compatible |
Yes |
Audio Performance
|
| Conversion resolution |
24-bit |
| Internal Sample Rate / Data path |
96 kHz / 32 bit floating point |
| Product propagation delay |
Best case (AES synchronous 96 kHz to AES synchronous 96 kHz via module) 0.871 ms Analog (Analog in to Analog out via module) 1.039 ms Pass thru (Analog in to AES synchronous 96 kHz bypassing module) 0.158 ms |
| Maximum available user delay |
2 seconds |
Analog
|
| Inputs and Outputs |
2 inputs, 6 outputs |
| Frequency response, digital-to-analog |
+/-0.03 dB, 20 Hz to 20 kHz |
| Frequency response, analog-to-digital |
+/-0.1 dB, 20 Hz to 20 kHz |
| THD+Noise, inputs |
0.00024% typical at 1 kHz |
| THD+Noise, Outputs |
0.00037% typical at 1 kHz |
| Dynamic range, inputs |
116 dB |
| Dynamic range, Outputs |
115 dB |
| Input impedance |
20 kOhm balanced, 10 kOhm unbalanced |
| Common Mode Rejection (CMR) |
-74 dB, 20 Hz to 20 kHz |
| Crosstalk, inputs |
-98 dB, 20 Hz to 20 kHz |
Dante Audio Network
|
| Inputs and Outputs |
4 inputs, 8 outputs |
| Supported sample rates |
48, 96 kHz |
| Support redundant paths |
Yes |
| Flexible topology |
yes |
Device presets
|
| Frame presets |
100 |
AES Inputs
|
| Inputs and Outputs |
4 inputs, 8 outputs |
| Supported resolutions |
Up to 24-bit |
| Supported sample rates |
44.1, 48, 88.2, 96, 176.4, 192 kHz |
| Termination |
Selectable |
| GPIO |
| Inputs |
2 General Purpose Inputs (GPI) supporting external contact closure |
| Outputs |
2 General Purpose Outputs (GPO) with internal contact closure |
| Software configurable input control |
Standby state, Mute state, Dual preset recall |
| Software configurable output indication |
Standby state, Mute state, Faults, Ready |
Ethernet
|
| Gigabit Ethernet |
1000 Base-T |
| Fast Ethernet |
100 Base-Tx |
Back panel Interface
|
| Analog Inputs and Outputs |
2 + 6 XLR |
| AES Inputs and Outputs |
DB-25, with selectable termination |
| Ethernet Ports |
Dual Neutrik® etherCON® |
| GPIO |
DB-9 |
| Power |
Detachable locking 3-pin IEC |
| Control and monitoring interface |
Via Ethernet for Lake Controller software |
Front-panel user interface
|
| Display |
Daylight readable monochrome (128 x 64) |
| Meters |
LED for signal level and clip indicators per channel |
| LED Fault and Warning indication |
Yes |
| Parameter adjustment |
Single/multiple parameter edits with rotary encoder |
| Standby Power button |
On/Standby |
Power
|
| Nominal voltage |
100 – 240 VAC |
| Operating voltage |
70-265 V AC |
| Power consumption |
30 W maximum |
Dimensions
|
| Dimensions |
483 mm (19″), 44 mm (1 U), 290 mm (11.5″) |
| Weight |
5 kg (11 lbs) |
| Finish |
Black painted steel chassis with cast alumimum handles |
| Approvals |
CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC |
